下面的代碼是用PS2鍵盤控制LED顯示按鍵編碼.按住顯示的是通碼.放開顯示的是斷碼.但由于斷碼最后8位是通碼一樣(不包括多位通碼).所以顯示一般是一樣的.

單片機P3.3接PS2按口的5為時鐘CLK,P3.4接PS2接口的1為數據DATA,因?yàn)閱纹瑱C(jī)初始并口輸出為全1,所以數據線與時鐘線都為1,而PS2發數據時,由鍵盤產生時鐘信號與數據信號,發完數據線信號與時鐘線信號都變?yōu)楦?

代碼如下:

#include
#include

#define ESC_CODE 0x76 //ESC鍵碼

sbit PS2_DATA = P3^4; //PS2數據線
sbit PS2_CLK = P3^3; //PS2時鐘線

sbit BEEP = P3^7; //蜂鳴器驅動線

unsigned char TEMP;

unsigned char KeyCode; //鍵盤鍵值

unsigned char code TABLE_D[] = { //鍵值碼

0x1c,0x32,0x21,0x23,0x24,0x2b,0x34,0x33,0x43,0x3b,0x42,

0x4b,0x3a,0x31,0x44,0x4d,0x15,0x2d,0x1b,0x2c,0x3c,0x2a,0x1d,0x22,0x35,0x1a, //a-z

0x45,0x16,0x1e,0x26,0x25,0x2e,0x36,0x3d,0x3e,0x46, //0-9

0x0e,0x4e,0x55,0x5d,0x29,0x54,0x5b,0x4c,0x52,0x41,0x49,0x4a,0x71, //標點符號

0x70,0x69,0x72,0x7a,0x6b,0x73,0x74,0x6c,0x75,0x7d, //右邊數字鍵0-9

0xff };

void delay(unsigned int x)
{
unsigned char i;
while(x--)
{
for (i=0; i<13; i++) ;
}
}

void beep()
{
unsigned char i;
for (i=0;i<100;i++)
{
delay(5);
BEEP=!BEEP; //BEEP取反
}
BEEP=1; //關閉蜂鳴器
}

unsigned char ReadPS2()
{
unsigned char i; //位數
while(PS2_CLK); //等待鍵盤把時鐘第一次拉低，表示

for(i=8; i!=0; i--) // 把起始位算入
{
while(!PS2_CLK); //等待一個有效的下跳沿，這兩條while是半個周期,主設備在下降沿讀數據
while( PS2_CLK);
KeyCode >>= 1; //數據低位在前

if(PS2_DATA == 1)
KeyCode |= 0x80; // 得到有效的數據位
}

for(i=2;i!=0;i--) //等待鍵盤發送效驗位和終止位
{
while(!PS2_CLK);
while( PS2_CLK);
}

while(!PS2_CLK); //等待鍵盤把時鐘線拉高

TEMP = KeyCode;
TEMP = ~TEMP;
P2=TEMP; //顯示鍵碼

return(KeyCode); //返回按鍵值
}

void PS2KEY()
{
unsigned char y;

for(y=0 ;y<60 ;y++) //鍵值變換為順序碼
{
if(KeyCode==TABLE_D[y])
{
delay(1000);
beep() ; //查找有效，蜂鳴器響一聲
}
}
}

void main()
{
P2 = 0xff; //關閉所有LED

while(1)
{
ReadPS2();
if(KeyCode==ESC_CODE) //Esc鍵碼
{
P2 = 0xff; //關閉所有LED
}
PS2KEY();
}
}

/*********************************************************/